Install 10 LED Downlights cost in Australia
Supply and install ten LED downlights in an existing ceiling with roof access. Compare modelled costs, what is and isn't included, and city adjustments — then check your own quote against it.
$600–$1,200
Midpoint estimate: $900 per job
Install 10 LED Downlights · Sydney. Modelled estimate, not calculated from consumer submissions. GST included; city, suburb and materials differences are assumptions rather than observed prices. Confirm scope and inclusions with the provider.
How this figure is put together
Estimate from our published model, labelled as such; method and city factors on the page.
Modelled estimate. City, suburb and materials factors are assumptions, not observed price differences. Confirm GST, units and inclusions with the provider.
GST is included in this price basis.
No verified observation date for this model.
Existing guide assumptions; not a measured market sample or verified rate card.
National guide, modelled from the Sydney baseline and adjusted by city below.
Before booking: This model assumes materials are included; confirm the actual quote. This model assumes GST is included; confirm the provider’s GST treatment. Agree callout and additional work in the written total.
Per downlight, or one at a time
| How it is booked | Modelled total | Per downlight |
|---|---|---|
| A batch of 10, supplied and installed | $600–$1,200 | $60–$120 |
| A single fitting as its own job | $90–$280 | $90–$280 |
Both rows are modelled Sydney baseline estimates, not quotes or observed prices. The per-downlight figure divides the batch model by 10. A single job carries the whole attendance and minimum labour charge, which is why booking several at once usually costs less per downlight. The single-fitting model may be labour only where an existing fitting is replaced, so confirm what each quote supplies.
What changes a downlight quote
Roof access
The model assumes an existing ceiling with roof-space access. A two-storey home, a low or tiled roof, or no roof space at all means more labour; ask whether the quote allows for it.
New cable runs and switching
Swapping old fittings for new ones on existing wiring is quicker than adding new circuits, switches or dimmers. The model lists new switching and dimmers as extras.
Insulation
Ask whether the fittings suit contact with your ceiling insulation and whether any insulation has to be moved or replaced.
Old halogen transformers
Replacing halogens can mean removing transformers and enlarging or patching cut-outs. Ask whether making good the ceiling is included.
Fitting quality
Colour temperature, dimmable drivers and warranty length vary between fittings. Ask for the brand and model so two quotes compare like with like.
Prices by suburb: FairCost has no verified suburb-level downlight prices. Between homes in the same city, roof access, ceiling type and how much new wiring is needed usually matter more than the suburb, so describe those when you ask for a quote.
Materials
This model assumes materials are included; confirm the actual quote.
Fittings included; new switching or dimmers extra
GST & fees
This model assumes GST is included; confirm the provider’s GST treatment.
Modelled attendance allowance: $80–$150. Confirm whether it is included in the quote.
Install 10 LED Downlights prices by city
City figures apply local cost-of-living adjustments to the national guide.
Install 10 LED Downlights by city
Modelled ranges, not observed prices. The spread between cities comes from a published city multiplier applied to the national range — it is an assumption about each market, not a measurement of it.
On a small screen, scroll across to see every column.
| City | Typical range | Around |
|---|---|---|
| Sydney | $600 – $1,200 | $900 |
| Melbourne | $552 – $1,104 | $828 |
| Brisbane | $510 – $1,020 | $765 |
| Perth | $492 – $984 | $738 |
| Adelaide | $468 – $936 | $702 |
| Canberra | $558 – $1,116 | $837 |
| Hobart | $492 – $984 | $738 |
| Darwin | $528 – $1,056 | $792 |
| Gold Coast | $498 – $996 | $747 |
| Toowoomba | $468 – $936 | $702 |
| Ballarat | $504 – $1,008 | $756 |
| Bendigo | $498 – $996 | $747 |
| Townsville | $510 – $1,020 | $765 |
| Mackay | $552 – $1,104 | $828 |
| Albury-Wodonga | $480 – $960 | $720 |
Before accepting a install 10 led downlights quote
Use these questions to agree the scope before comparing totals.
- Work and quantity
- Ask the provider to define the install 10 led downlights work, quantity and exclusions in writing.
- Materials
- Fittings included; new switching or dimmers extra
- Price basis
- Confirm whether the charge is per job, and how additional work is agreed.
- Final amount
- Confirm callout, access, disposal, making good and GST treatment before approving the work.
FairCost editorial checklist. These are questions to agree with your provider, not promised inclusions.
What pushes a install 10 led downlights quote up
Estimate or verified?
Here install 10 led downlights prices on this page are modelled estimates using existing guide assumptions, without a reconciled source dataset. An observed range is published only when its numbers are computed from at least 10 eligible submissions with matching scope, tax and materials treatment. Quotes and paid invoices are kept separate. How we build estimates · Submit a price
Who can legally do this job
Licensing and permissions guidance
Electrical work: checked sources
On a small screen, scroll across to see every column.
| Location | Official source |
|---|---|
| NSW | Building Commission NSWAll electrical wiring work must be done by a licensed electrician, whatever the job costs. There is no small-job or DIY exemption. Whoever tests the work lodges a Certificate of Compliance for Electrical Work (CCEW) with Building Commission NSW within seven days; give them your email address so your copy reaches you. |
| VIC | Energy Safe VictoriaAll electrical work must be carried out by a licensed electrical worker working for a Registered Electrical Contractor. A Certificate of Electrical Safety must be issued for installation work and you receive a copy. Prescribed work such as switchboards and solar also requires independent inspection before it can be energised. |
| QLD | Electrical Safety Office (WorkSafe Queensland)Only a licensed electrical contractor may do electrical work in your home, with no dollar threshold. They must give a Certificate of Testing and Compliance to whoever engaged them, as soon as practicable after finishing. If a builder engaged the electrician the certificate goes to the builder, so ask the builder for it. |
| WA | Building and EnergyAll electrical work must be done by a person holding the relevant electrical licence, with no dollar threshold. The licensed contractor must give you an Electrical Safety Certificate within 28 days of finishing. Maintenance and like-for-like replacements are exempt. If the certificate does not arrive, contact your network operator. |
| SA | Office of the Technical RegulatorElectrical installation work must be done by a licensed and registered electrical worker. Your electrician must issue an electronic Certificate of Compliance (eCoC) within 30 days, confirming the work was tested and that they are correctly licensed. Minor maintenance such as changing a lightbulb is exempt. |
| TAS | Consumer Affairs TasmaniaElectrical work requires a practitioner licence, even when done unpaid, and there is no dollar threshold. For notifiable work the electrician completes a Certificate of Electrical Compliance and lodges it with TechSafe Australia within three days of energising; the certificate book includes a customer copy, so ask for yours. Like-for-like replacement generally needs no notification. |
| ACT | Access CanberraElectricians must be licensed for any electrical wiring work, with no dollar threshold. All wiring work must be tested and certified, and the electrician must give a certificate to the construction occupations registrar and to you as the owner of the installation. New installations are audited before they can be energised. |
| NT | NT WorkSafeIt is illegal to do your own electrical work in the NT unless you are licensed, so use a licensed electrical contractor. There is no dollar threshold. For alterations or additions the contractor must provide a Certificate of Compliance to the owner and occupier within 20 business days. Maintenance and like-for-like replacement are exempt. |
| Your location | Australian Business Licence and Information ServiceSearch the exact activity and location to find licensing, regulatory and council requirements. Follow through to the named authority and verify the provider separately. This lookup is not confirmation that a provider is licensed or a job is exempt. |
This is not a complete register of requirements. Where a state-specific source has not been checked, use the government lookup. Qualified trade review is pending; no universal licence exemption is asserted.
Electrical Work cost guides by city
Local pricing, licensing and quote checks for electrical work in each city we cover in detail.
Install 10 LED Downlights: common questions
Install 10 LED Downlights cost: how much should you pay?+
Are materials included in the price?+
Is GST included?+
Is there a callout fee?+
How long does it take?+
Does the person doing install 10 led downlights need a licence?+
Is this price an estimate or based on real quotes?+
See the full electrical work picture
Know someone getting quotes for this?
Install 10 LED Downlights price updates
Register interest in pricing research for this job. Modelled estimates and qualifying reported prices are labelled separately. Update timing is not guaranteed.