Install Power Point cost in Australia
Add a new single power point (existing circuit, easy access). Compare modelled costs, what is and isn't included, and city adjustments — then check your own quote against it.
$150–$380
Midpoint estimate: $265 per job
Install Power Point · Sydney. Modelled estimate, not calculated from consumer submissions. GST included; city, suburb and materials differences are assumptions rather than observed prices. Confirm scope and inclusions with the provider.
How this figure is put together
Estimate from our published model, labelled as such; method and city factors on the page.
Modelled estimate. City, suburb and materials factors are assumptions, not observed price differences. Confirm GST, units and inclusions with the provider.
GST is included in this price basis.
No verified observation date for this model.
Existing guide assumptions; not a measured market sample or verified rate card.
National guide, modelled from the Sydney baseline and adjusted by city below.
Before booking: This model assumes materials are included; confirm the actual quote. This model assumes GST is included; confirm the provider’s GST treatment. Agree callout and additional work in the written total.
Materials
This model assumes materials are included; confirm the actual quote.
Standard GPO and cable usually included. Premium fittings (USB, smart) extra.
GST & fees
This model assumes GST is included; confirm the provider’s GST treatment.
Modelled attendance allowance: $80–$150. Confirm whether it is included in the quote.
Install Power Point prices by city
City figures apply local cost-of-living adjustments to the national guide.
Install Power Point by city
Modelled ranges, not observed prices. The spread between cities comes from a published city multiplier applied to the national range — it is an assumption about each market, not a measurement of it.
On a small screen, scroll across to see every column.
| City | Typical range | Around |
|---|---|---|
| Sydney | $150 – $380 | $265 |
| Melbourne | $138 – $350 | $244 |
| Brisbane | $128 – $323 | $226 |
| Perth | $123 – $312 | $218 |
| Adelaide | $117 – $296 | $207 |
| Canberra | $140 – $353 | $247 |
| Hobart | $123 – $312 | $218 |
| Darwin | $132 – $334 | $233 |
| Gold Coast | $125 – $315 | $220 |
| Toowoomba | $117 – $296 | $207 |
| Ballarat | $126 – $319 | $223 |
| Bendigo | $125 – $315 | $220 |
| Townsville | $128 – $323 | $226 |
| Mackay | $138 – $350 | $244 |
| Albury-Wodonga | $120 – $304 | $212 |
Before accepting a install power point quote
Use these questions to agree the scope before comparing totals.
- Work and quantity
- Ask the provider to define the install power point work, quantity and exclusions in writing.
- Materials
- Standard GPO and cable usually included. Premium fittings (USB, smart) extra.
- Price basis
- Confirm whether the charge is per job, and how additional work is agreed.
- Final amount
- Confirm callout, access, disposal, making good and GST treatment before approving the work.
FairCost editorial checklist. These are questions to agree with your provider, not promised inclusions.
What pushes a install power point quote up
Estimate or verified?
Here install power point prices on this page are modelled estimates using existing guide assumptions, without a reconciled source dataset. An observed range is published only when its numbers are computed from at least 10 eligible submissions with matching scope, tax and materials treatment. Quotes and paid invoices are kept separate. How we build estimates · Submit a price
Who can legally do this job
Licensing and permissions guidance
Electrical work: checked sources
On a small screen, scroll across to see every column.
| Location | Official source |
|---|---|
| NSW | Building Commission NSWAll electrical wiring work must be done by a licensed electrician, whatever the job costs. There is no small-job or DIY exemption. Whoever tests the work lodges a Certificate of Compliance for Electrical Work (CCEW) with Building Commission NSW within seven days; give them your email address so your copy reaches you. |
| VIC | Energy Safe VictoriaAll electrical work must be carried out by a licensed electrical worker working for a Registered Electrical Contractor. A Certificate of Electrical Safety must be issued for installation work and you receive a copy. Prescribed work such as switchboards and solar also requires independent inspection before it can be energised. |
| QLD | Electrical Safety Office (WorkSafe Queensland)Only a licensed electrical contractor may do electrical work in your home, with no dollar threshold. They must give a Certificate of Testing and Compliance to whoever engaged them, as soon as practicable after finishing. If a builder engaged the electrician the certificate goes to the builder, so ask the builder for it. |
| WA | Building and EnergyAll electrical work must be done by a person holding the relevant electrical licence, with no dollar threshold. The licensed contractor must give you an Electrical Safety Certificate within 28 days of finishing. Maintenance and like-for-like replacements are exempt. If the certificate does not arrive, contact your network operator. |
| SA | Office of the Technical RegulatorElectrical installation work must be done by a licensed and registered electrical worker. Your electrician must issue an electronic Certificate of Compliance (eCoC) within 30 days, confirming the work was tested and that they are correctly licensed. Minor maintenance such as changing a lightbulb is exempt. |
| TAS | Consumer Affairs TasmaniaElectrical work requires a practitioner licence, even when done unpaid, and there is no dollar threshold. For notifiable work the electrician completes a Certificate of Electrical Compliance and lodges it with TechSafe Australia within three days of energising; the certificate book includes a customer copy, so ask for yours. Like-for-like replacement generally needs no notification. |
| ACT | Access CanberraElectricians must be licensed for any electrical wiring work, with no dollar threshold. All wiring work must be tested and certified, and the electrician must give a certificate to the construction occupations registrar and to you as the owner of the installation. New installations are audited before they can be energised. |
| NT | NT WorkSafeIt is illegal to do your own electrical work in the NT unless you are licensed, so use a licensed electrical contractor. There is no dollar threshold. For alterations or additions the contractor must provide a Certificate of Compliance to the owner and occupier within 20 business days. Maintenance and like-for-like replacement are exempt. |
| Your location | Australian Business Licence and Information ServiceSearch the exact activity and location to find licensing, regulatory and council requirements. Follow through to the named authority and verify the provider separately. This lookup is not confirmation that a provider is licensed or a job is exempt. |
This is not a complete register of requirements. Where a state-specific source has not been checked, use the government lookup. Qualified trade review is pending; no universal licence exemption is asserted.
Electrical Work cost guides by city
Local pricing, licensing and quote checks for electrical work in each city we cover in detail.
Install Power Point: common questions
Install Power Point cost: how much should you pay?+
Are materials included in the price?+
Is GST included?+
Is there a callout fee?+
How long does it take?+
Does the person doing install power point need a licence?+
Is this price an estimate or based on real quotes?+
See the full electrical work picture
Know someone getting quotes for this?
Install Power Point price updates
Register interest in pricing research for this job. Modelled estimates and qualifying reported prices are labelled separately. Update timing is not guaranteed.