Tap Repair / Replacement cost in Australia
Repair leaking tap or replace mixer/tap. Compare modelled costs, what is and isn't included, and city adjustments — then check your own quote against it.
$130–$400
Midpoint estimate: $265 per job
Tap Repair / Replacement · Sydney. Modelled estimate, not calculated from consumer submissions. GST included; city, suburb and materials differences are assumptions rather than observed prices. Confirm scope and inclusions with the provider.
How this figure is put together
Estimate from our published model, labelled as such; method and city factors on the page.
Modelled estimate. City, suburb and materials factors are assumptions, not observed price differences. Confirm GST, units and inclusions with the provider.
GST is included in this price basis.
No verified observation date for this model.
Existing guide assumptions; not a measured market sample or verified rate card.
National guide, modelled from the Sydney baseline and adjusted by city below.
Before booking: Materials treatment is not fixed in this model; ask what the written total covers. This model assumes GST is included; confirm the provider’s GST treatment. Agree callout and additional work in the written total.
Materials
Materials treatment is not fixed in this model; ask what the written total covers.
Washer replacement is labour-only. Full tap replacement excludes the tap unit ($80–$400+).
GST & fees
This model assumes GST is included; confirm the provider’s GST treatment.
Modelled attendance allowance: $80–$150. Confirm whether it is included in the quote.
Tap Repair / Replacement prices by city
City figures apply local cost-of-living adjustments to the national guide.
Tap Repair / Replacement by city
Modelled ranges, not observed prices. The spread between cities comes from a published city multiplier applied to the national range — it is an assumption about each market, not a measurement of it.
On a small screen, scroll across to see every column.
| City | Typical range | Around |
|---|---|---|
| Sydney | $130 – $400 | $265 |
| Melbourne | $120 – $368 | $244 |
| Brisbane | $111 – $340 | $226 |
| Perth | $107 – $328 | $218 |
| Adelaide | $101 – $312 | $207 |
| Canberra | $121 – $372 | $247 |
| Hobart | $107 – $328 | $218 |
| Darwin | $114 – $352 | $233 |
| Gold Coast | $108 – $332 | $220 |
| Toowoomba | $101 – $312 | $207 |
| Ballarat | $109 – $336 | $223 |
| Bendigo | $108 – $332 | $220 |
| Townsville | $111 – $340 | $226 |
| Mackay | $120 – $368 | $244 |
| Albury-Wodonga | $104 – $320 | $212 |
Tap repair or replacement: compare the same work
Compare matching work before comparing totals. These are scope questions, not diagnoses or guaranteed inclusions.
Repair the existing tap
Ask which fault and internal part the repair addresses.
Compare: Diagnosis, part, labour and what happens if the leak remains.
Install a tap you supply
Ask the plumber to confirm that the proposed fixture suits the existing installation.
Compare: Installation labour, connections, disposal and any separately priced adaptations.
Supply and install a replacement
Have the provider name the exact fixture in the quote.
Compare: Fixture supply plus installation, GST treatment and the agreed final total.
Adapt this message for your quote request
Please quote for the tap problem shown in my photos. State whether you propose repair or replacement, the part or fixture included, callout and labour, any exclusions, and the total payable. Please obtain my agreement before additional work.
FairCost editorial guidance. Send only the details needed by your chosen provider.
What to check if the final bill changesCompare a tap repair with a full replacement
Ask each plumber to price the same outcome. Replacing an internal part and supplying a new mixer are different jobs; a single headline figure cannot tell you which is included.
- Repair scope
- Which fault was diagnosed, which part is being replaced, and what happens if the repair does not resolve the leak?
- Replacement scope
- What exact tap or mixer is included? If you supply it, will the plumber confirm suitability before attending?
- Attendance and labour
- Is the callout included in the total? Is labour fixed for the agreed work or charged by time?
- Additional work
- Ask whether isolation valves, flexible connections, access repairs and disposal are included or separately quoted.
- Final total
- Confirm GST treatment, the amount payable, and how any additional work will be agreed before it starts.
For a replacement, compare water-use information where WELS applies. Bath taps and spouts are an exception. A water-efficiency rating does not establish the installed price.
Australian Government: understanding WELS star ratingsSource checked 14 October 2026. The checklist is FairCost’s editorial guidance for comparing quotes.
What pushes a tap repair / replacement quote up
Estimate or verified?
Here tap repair / replacement prices on this page are modelled estimates using existing guide assumptions, without a reconciled source dataset. An observed range is published only when its numbers are computed from at least 10 eligible submissions with matching scope, tax and materials treatment. Quotes and paid invoices are kept separate. How we build estimates · Submit a price
Who can legally do this job
Licensing and permissions guidance
Plumbing and drainage: checked sources
On a small screen, scroll across to see every column.
| Location | Official source |
|---|---|
| NSW | Building Commission NSWA licence is required for any plumbing, draining or gasfitting work in NSW regardless of the cost of the work, so there is no small-job exemption. Your plumber lodges a Notice of Work before starting and, at completion, must give you a Certificate of Compliance, which is also submitted to Building Commission NSW or, in regional areas, to the council acting as plumbing regulator. If the job involved drainage work you should also receive a Sewer Service Diagram. Ask for both documents before you pay the final invoice. Minor and emergency work is treated differently: NSW guidance says a Notice of Work is not required for jobs such as replacing tapware or an existing hot-water system, or a bathroom renovation that does not move fixtures, and a Certificate of Compliance for work that did not need inspection is given to you but not lodged with the regulator. So for a tap repair, expect the certificate, not a filing. |
| VIC | Building and Plumbing CommissionPlumbing work in Victoria must be done by a registered or licensed plumber. Where the total value of the work exceeds $750 — including materials, appliances, labour and GST — your plumber must give you a compliance certificate within five days of finishing and lodge it with the BPC within five days. Some work requires a compliance certificate whatever it costs, including Type A gas appliance installation and below-ground sanitary drain work. Work valued at $750 or less does not attract a compliance certificate but must still be done by a registered plumber. |
| QLD | Queensland Building and Construction CommissionAll regulated plumbing and drainage work in Queensland must be done by a licensed plumber or drainer, and the QBCC publishes no dollar threshold for it. For notifiable work — a bathroom renovation or a water heater replacement, for example — your plumber registers the job with the QBCC on a Form 4 within 10 business days of issuing an invoice, and must give a copy to the owner of the premises or to whoever engaged them. Keep that copy: it is your record that the work was notified. Plumbing that forms part of new construction is permit work rather than notifiable work and goes through your council instead. |
| WA | Plumbers Licensing Board (Building and Energy)Only the holder of a plumber's licence from the Plumbers Licensing Board may carry out plumbing work in WA, at any job value. For major plumbing work your plumber lodges a Notice of Intention at least 24 hours before starting, then a Certificate of Compliance within five working days of completing the work, and must give you the owner's copy. Minor plumbing work — testing, maintenance, repair or like-for-like replacement, such as a tap repair — is exempt from the certificate; the contractor keeps a record instead. Replacing a water heater or a testable backflow prevention device is always major work, so those jobs do carry a certificate. |
| SA | Office of the Technical RegulatorIn South Australia the business doing the work must hold a plumbing, gas fitting and electrical contractor's licence from Consumer and Business Services, and the tradesperson doing the work must be registered. Plumbing work must be certified: the electronic certificate of compliance (eCoC) must be submitted within seven days of the job being completed. You cannot access the eCoC portal yourself, so ask your plumber to email you the certificate. The seven-day limit is specific to plumbing — gas work allows 30 days. Some everyday jobs are exempt from certification under the SA guidance, including changing tap washers, clearing blocked drains, installing domestic tapware and installing stormwater systems; for those, a compliant job will not come with an eCoC, and that is not a warning sign. |
| TAS | Building Standards TasmaniaAny plumbing work that is not Category 1 low-risk work must be done by a licensed plumber; the test is the risk category of the work, not its price. For notifiable work such as a kitchen or bathroom renovation your plumber lodges a Notice of Work with the council as permit authority and obtains a Certificate of Likely Compliance before starting, and higher-risk work requires a plumbing permit as well. The completion document is the Certificate of Completion – Plumbing Work (Form 21). Category 1 work you may do yourself, including like-for-like tapware replacement, shower rose repairs, cistern valve repairs, changing a water filter cartridge and plunging a blocked toilet. |
| ACT | Access CanberraPlumbers, drainers and gasfitters must be licensed in the ACT, with no dollar threshold on the licence itself. A threshold applies only to plan approval: the plan approval system does not apply to minor plumbing or drainage work, meaning replacement and repairs up to a value of $1,000. That minor work must still be carried out by a licensed plumber and drainer and requires a hydraulic compliance certificate for minor works, lodged with Access Canberra. For larger jobs your plumber notifies Access Canberra before starting, when the work is ready for inspection and at completion, and registers certified final drainage and plumbing plans before a final inspection can be booked. |
| NT | NT Plumbers and Drainers Licensing BoardOnly licensed plumbers and drainers can be engaged in the Territory's declared plumbing licence areas, and no dollar threshold applies. For plumbing and drainage work that does not involve other building work, a certifying plumber or drainer — a licensed plumber who is also registered with the Building Practitioners Board — issues a Certificate of Compliance (plumbing and drainage works) on completion, and the notice and certificate must be lodged with the Director of Building Control within seven days. A journeyman is not a licensed plumber and cannot contract directly with you. Minor maintenance, repairs and like-for-like replacements are not treated as plumbing or drainage work, so they need no certificate — unblocking a toilet with mechanical tools, for example. |
| Your location | Australian Business Licence and Information ServiceSearch the exact activity and location to find licensing, regulatory and council requirements. Follow through to the named authority and verify the provider separately. This lookup is not confirmation that a provider is licensed or a job is exempt. |
This is not a complete register of requirements. Where a state-specific source has not been checked, use the government lookup. Qualified trade review is pending; no universal licence exemption is asserted.
Plumbing cost guides by city
Local pricing, licensing and quote checks for plumbing in each city we cover in detail.
Tap Repair / Replacement: common questions
Tap Repair / Replacement cost: how much should you pay?+
Are materials included in the price?+
Is GST included?+
Is there a callout fee?+
How long does it take?+
Does the person doing tap repair / replacement need a licence?+
Is this price an estimate or based on real quotes?+
See the full plumbing picture
Know someone getting quotes for this?
Tap Repair / Replacement price updates
Register interest in pricing research for this job. Modelled estimates and qualifying reported prices are labelled separately. Update timing is not guaranteed.